⚙️ Jam Clearing · Reset · Leak Repair · Replacement
Professional Garbage Disposal Repair in High Point, NC — All Brands, Same-Day Service
Your disposal hums but won't spin — the impeller plate is jammed. It's completely silent when you flip the switch — the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar — the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in High Point, NC arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
Jam Clearing & ResetInSinkErator, Moen, Waste KingSink Collar Leak RepairSame-Day Replacement Units
Why Call Masters Plumbing Service for Disposal Work
4 Things That Set Our Garbage Disposal Repair Service Apart in High Point, NC
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units — they identify what failed and whether repair or replacement is the right call for your situation.
🔎
Symptom-Specific Diagnosis
Hum but no spin: jammed impeller. No sound at all: tripped thermal overload or failed motor. Intermittent operation: loose wiring at the switch or disposal unit. Continuous drain from the sink collar: failed sink flange gasket. Leak from the side: dishwasher drain hose connection or internal body crack. We trace the symptom to the specific cause before recommending any solution.
🏷️
All Major Brands Serviced
InSinkErator models use a 1/4-inch Allen wrench at the center bottom; Waste King models use a broom-handle approach at the top. Knowing which you have before arriving saves time and prevents the wrong tool damaging the motor shaft.
💲
Repair vs. Replace — Honest Guidance
A disposal that jams once is worth clearing and resetting. A disposal that jams repeatedly, has a seized turntable bearing, emits burning smells, or is over 10 years old is likely approaching motor failure — and the repair cost of a failed motor exceeds the cost of a new unit.
🔧
Full Plumbing Integration Check
A disposal installed without properly removing the dishwasher drain knockout plug is a common installation error that floods the dishwasher interior. We check this and correct it if present.
Our Services
Every Garbage Disposal Repair Issue We Handle in High Point, NC
Most disposal calls complete in 30–60 minutes — same visit, flat-rate pricing.
Jammed
Jam Clearing & Reset
A disposal that hums with no rotation has a jammed impeller plate — the spinning plate has been stopped by a bone fragment, a piece of silverware that fell in, or hard food buildup around the shredder ring. We use the jam-clearing wrench at the center motor socket to manually rotate the impeller free, remove any obstruction from the grinding chamber, and press the thermal overload reset button before testing.
Won't Start
Reset & Electrical Diagnosis
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
Leaking
Sink Collar & Connection Leak Repair
Disposal leaks come from three locations: the sink flange (top of the unit where it mounts to the sink drain opening — repaired by re-sealing the flange with plumber's putty and re-tightening the mounting ring), the side port (dishwasher drain hose connection — usually a loose hose clamp or cracked fitting), or the bottom of the unit (internal body crack or failed internal seal — indicates replacement needed).
Noisy
Noise Diagnosis & Repair
An unusually loud grinding, rattling, or metal-on-metal sound from a disposal almost always means either a hard object (bottle cap, small utensil, pit from stone fruit) is in the grinding chamber, or an impeller piece has broken and is contacting the shredder ring. We access the grinding chamber safely, remove any foreign objects, and inspect the impeller and shredder ring for damage.
Draining
Slow Drain & Drain Line Clearing
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
Replacement
Full Disposal Replacement
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
Our Garbage Disposal Repair Diagnosis & Repair Workflow in High Point
A disposal call takes 30–60 minutes in most cases. Here's exactly how it goes — from your first call to a clean, functional kitchen drain.
1
Describe the Symptom — We Prep Accordingly
If you know the disposal is over 10 years old, tell us — that changes how we approach the repair-vs-replace conversation upfront.
2
On-Site Diagnosis — Specific, Fast
The tech identifies the failure type in minutes: jam test at the motor socket, reset button check, power confirmation at the wire connections, leak source tracing. We know what each symptom means and we go straight to confirming it.
3
Flat-Rate Quote — Repair or Replace
You receive a flat-rate price for the repair option and, if relevant, the replacement option with unit cost included. For a simple jam clear, that's a single, low line item. For a failed motor, we show you the new unit cost and installation price together.
4
Repair or Install — Test Everything Before Leaving
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.
Customer Reviews
What High Point Homeowners Say About Our Disposal Repairs
★★★★★
Disposal hummed and wouldn't spin. I'd already tried the Allen wrench trick without success. Masters Plumbing Service's tech came out, worked the impeller free from underneath while removing a piece of broken ceramic that had fallen in — it had wedged between the impeller and the grinding ring in a way I couldn't have cleared from the top. Cleared the jam, pressed the reset, tested. Five-minute fix. Honest about the call minimum charge, no attempt to upsell a replacement on a perfectly good motor.
— E. Park, High Point
★★★★★
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately — the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
— J. & L. Maher, High Point, NC
★★★★★
Disposal leaking from the sink collar area. Previous owner had installed it with silicone instead of plumber's putty at the flange — silicone doesn't hold the mounting pressure correctly and had separated. Tech re-seated the flange with putty, re-tightened the mounting ring, and the leak stopped. Tested with a full minute of running water. All clear.
— Y. Okonkwo, High Point, NC
Common Questions
What to Know Before Calling for Garbage Disposal Repair in High Point, NC
A hum without rotation almost always means a jammed impeller — not a failed motor. The motor is running (hence the hum) but the turntable is blocked. Try inserting a 1/4-inch Allen wrench into the center socket at the bottom of the disposal and working it back and forth to free the impeller, then press the red reset button on the bottom and try again.
Replacement makes more sense when: the motor has completely failed (no hum, power confirmed, reset button doesn't help), the unit body is cracked and leaking from the bottom, the grinding chamber is heavily corroded or chipped, or the unit is over 10 years old with multiple issues. A new 1/2 HP disposal costs significantly less than the labor of rebuilding an old motor that will likely fail again.
The items that create the most disposal problems in High Point, NC homes: large bones (chicken bones and small fish bones are fine; large beef and pork bones are not), fibrous vegetables (celery, artichoke leaves, asparagus — the fibers wrap around the impeller shaft), starchy foods in large quantities (pasta, rice, and potato peels expand with water and can pack the drain arm), and fats, oils, and grease in significant amounts (they resolidify in the drain arm, not in the grinding chamber).
Persistent odor after cleaning the chamber often means food has packed into the drain arm — a short section of PVC between the disposal outlet and the p-trap. Disconnecting and cleaning this arm completely clears the odor source.
Well-maintained garbage disposals typically last 10–15 years. InSinkErator's evolution series and other higher-horsepower units with stainless steel grinding components tend toward the high end; entry-level units with less robust construction toward the lower end. Usage frequency, water hardness, and what goes into the disposal all affect longevity.
A plumber handles the plumbing side; if a new electrical circuit or switch is needed, we coordinate with an electrician. Most swap-out replacements where the existing circuit and switch are functional are purely a plumbing call.
Service Area
Garbage Disposal Repair Available Across High Point and High Point, NC
Our trucks carry replacement disposal units in common horsepower ratings for same-day installation when the motor has failed.
Jammed, Leaking, or Dead Disposal in High Point? Call +1-855-718-1500
Our disposal techs in High Point, NC carry the tools and replacement units to resolve any disposal problem same visit. Flat-rate pricing, honest repair-vs-replace guidance, and no unnecessary upselling.
